Exactly How to Remove and Also Change a Bathtub
Exactly How to Remove and Also Change a Bathtub
Blog Article
What are your opinions about How to Install a Bathtub Yourself?
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily obtainable, the job can move speedily; if you need to open a wall to get rid of the old tub and place the new bath tub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might need a professional plumber to make tube links.
This article will certainly help you set up a new tub in your bathroom if you have actually already gotten a new bathtub and do not require to alter the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the faucet in position with the maker provided backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub till the spirit level reads degree.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and examine all joints and also new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been made use of at least when as this will resolve it into its final setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, creating the water to penetrate the wall between the bath as well as the tiling, bring about complications with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on A Step-by-Step Guide to Installing a Bathtub, I thought sharing that piece of content was a good thing. Kindly take the time to promote this post if you appreciated it. Thank you for your time invested reading it.
Booking
Report this page